This week on the Budget LN106 hilux 4 Runna build we take some box steel and turn it into a front drive shaft aka the box shaft. Fit Chromoly Axles and CVs as well as a Harrop E locker. Also finishing that of with a fresh axle rebuild! 🔥 ROAM LYFE MERCH / WEBSITE ► https://roamlyfe.com 🧼 FOAM LYFE - 4x4 Wash That Actually Works www.foamlyfe.com.au Harrop E Locker: https://www.harrop.com.au/ 📸 FOLLOW ROAM LYFE Instagram → https://instagram.com/roamlyfe YouTube → https://youtube.com/@RoamLyfe ⚡ Powered by iTechWorld – The Power Experts Get your gear here → https://itechworld.com.au Use code ROAMLYFE5 for a discount. 🚙 Suspension Setup Superior Engineering → https://www.superiorengineering.com.au/roamlyfe Check The box that says "Where did you hear about us" ROAM LYFE SparesBox: https://www.sparesbox.com.au/ 🎥 Filmed & Produced by Roam Lyfe Business enquiries: [email protected] #4WD #CampingAustralia #4x4Build #TouringAustralia #RoamLyfe #superiorengineering #superior4x4 @superior4x4 @superiorengineering
ADVERTISEMENT
Would have been cool to see this thing on kinchrome build wars
You should get sponsored by Ryobi, I sent them a message asking them to sponsor you. Keep up the good work
Box shaft will be fine nearly every LN owner on a budget has one 😂😂 When’s the LN glassy meet though?
I love that this video had both superior engineering and budget engineering 😂😂. Great video as always mate 🤙
diesel got the soul of an old bloke
Smacking those wheel studs in with a socket extension 😂😂. Luxy is looking mint. Time to LS it now!
I wouldn’t put chromoly hubs on it tho, keep it standard hub - or ur next weak point will be diff. Easier to replace a Hub than diff
Should done wide track while you were at it with the hubs
When this beast has all the good bits underneath, it’s gonna need more power… I reckon you run a comment comp to decide what gets swapped in. My vote: 1UZ / 2UZ / 3UZ. Not only will it sound absolutely feral and go hard as hell, but your video series will go viral AF. Every UZ-swapped build series on the internet absolutely froths views.
The big LN is getting so close to being done 🎉
Cant wait to see it out drive the patrol 😂 good as with the drive shaft might have to get one made one day though.
Hey mate love the videos but as someone that builds drive shafts for a living that was hard to watch 😅 😂
It looks awesome
Shame you couldn't do your slip shaft extension the other way around, so the receiver is at the lower point, you'd have better grease retention that way, as it would naturally fall into the receiver with gravity
Some sliders to finish it off 👌
Go road runner awesome boys great seeing the drone shots our back yard and mighty 60 made its appearance the drone shots getting even better as messaging that Prado the surprise packet but didn’t see wrecket Timmy boys in the gu wagon the winner for sure hurts as a Toyota brain well done all can’t wait build wars 3 depends on the Prado legally survive 😂 has to be outback or to the tip so shed life boys don’t have to travel as far all vehicles are capable so same budget just friggin awesome 🤘🤘🤘😁😁
Up the Luxy build so close 🎉smash the hype points legends🎉
Can you come do my bearings seals and brakes, been holding off on doing it for ages
Luxy is looking awesome man grats on the build. 👍
Congrats on sub numbers, you've earnt every single one of them, good mix of content appealing to broad numbers. 👏👏👏 Put a grease nipple in the large box section of your tail shaft close as possible to uni joint, then you can keep it well lubed as well as repel water ingress simply by greasing it up and force contaminated water out. Will also be sure it remains quite, no clatter as it can't run dry. Win, Win situation.